Michigan SOS CDL General Knowledge Practice Test 9

  • Questions50
  • Correct to pass40
  • Passing score80%
  • Minimum age18 years

50 questions. Pick an answer to see if it is right and why; you need 40 correct answers to pass.

  1. 1. An automatic transmission is left in its normal drive position as the vehicle rolls down a long grade. What does it tend to do?

    Show answer

    Answer A: Shift up as road speed rises, so engine braking falls away

    An automatic left in drive keeps upshifting as speed builds, which is the opposite of what you want on a grade; that is why the driver must select a low range.

  2. 2. The only way into a customer yard forces you to back toward the right, or blind, side of the vehicle. What should you do?

    Show answer

    Answer D: Use a helper and get out to check the path more often than you normally would

    Blind side backing is allowed but far riskier, so it calls for a spotter you can see and for repeated checks of the path on foot.

  3. 3. A load overhangs the rear of the trailer. What must the driver check before leaving?

    Show answer

    Answer D: That the overhang is marked as required, with flags or lamps as conditions demand

    A projecting load has to be made visible to other drivers, with flags in daylight and lamps when lights are required, so nobody runs into what they cannot see.

  4. 4. Where are the OVERSIZE LOAD signs normally carried on a vehicle moving under such a permit?

    Show answer

    Answer A: On the front and the rear of the vehicle

    The warning signs face the traffic that meets the load and the traffic that comes up behind it, so they go on the front and the rear.

  5. 5. A commercial vehicle stops on the shoulder of an undivided two-lane road that carries traffic in both directions. Where do the warning devices go?

    Show answer

    Answer B: Within 10 feet of the vehicle, plus 100 feet to the front and 100 feet to the rear

    On a two-way road the devices must mark the vehicle itself and warn traffic approaching from each direction, and they must be in place within ten minutes.

  6. 6. Why should you never shift gears while crossing railroad tracks?

    Show answer

    Answer A: You could miss the gear or stall and be stuck on the tracks

    A stalled or coasting vehicle on the tracks has no way to clear quickly, so choose the gear before the crossing and do not shift until you are across.

  7. 7. The temperature is around freezing and the road looks wet. What is a practical way to tell whether it is icy?

    Show answer

    Answer C: Check for ice building up on the mirrors, antenna or the front of the vehicle

    Ice that forms on the mirror, antenna or windshield is a warning that the road surface is freezing too, and black ice can look like a wet road.

  8. 8. Which situations call for a mirror check in a commercial vehicle?

    Show answer

    Answer A: Every lane change, turn, merge and tight maneuver

    Mirrors must be checked regularly and always before, during and after any movement that changes the path of the vehicle.

  9. 9. You are loading a flatbed that has no sides or bulkheads. How must the cargo be held?

    Show answer

    Answer D: By tiedowns, blocking or bracing, since there are no walls to keep it from shifting or falling off

    Open decks depend entirely on securement devices; every article must be tied down or otherwise immobilized so it cannot move, spill or fall.

  10. 10. At the end of the day you find no defects on a property carrying vehicle. What does the federal rule require?

    Show answer

    Answer B: No written report is required, although the carrier may still ask for one

    For property carrying vehicles the report is required only when a defect or deficiency is found or reported, although a carrier may impose a stricter policy.

  11. 11. A hazard suddenly appears ahead and you must act. Which is usually the faster way to avoid it in a heavy vehicle?

    Show answer

    Answer B: Steering around it, because you can usually turn faster than you can stop

    Stopping distance at speed is very long, so a quick turn out of the way, when there is room, avoids the crash sooner than braking.

  12. 12. You are pulling away from the curb after a delivery. Why is a mirror check needed first?

    Show answer

    Answer B: A cyclist or a vehicle may be coming up alongside you

    Traffic and cyclists can arrive alongside a parked vehicle at any moment, so the mirrors must be checked immediately before pulling out.

  13. 13. When must a post-trip inspection be made?

    Show answer

    Answer D: At the end of each day the driver operates the vehicle

    The post-trip inspection closes out each driving day so that anything found is recorded before the vehicle is handed to the next driver.

  14. 14. Using the snub braking method on a downgrade, when does the driver release the brakes?

    Show answer

    Answer A: After speed has dropped about 5 mph below the safe speed

    The driver brakes firmly to about 5 mph under the chosen safe speed, releases to let the brakes cool, then repeats when the safe speed returns.

  15. 15. How long must the record of a periodic inspection be kept?

    Show answer

    Answer A: Fourteen months

    The periodic inspection report is retained for fourteen months from the date of the report, which covers the full twelve month cycle plus a margin.

  16. 16. What is the driver looking for when the exhaust system is inspected?

    Show answer

    Answer B: Loose, broken or missing pipes, brackets or clamps, and signs that exhaust is leaking

    A loose or leaking exhaust system can send carbon monoxide into the cab and can put hot gas against parts that will burn.

  17. 17. At the scale your tractor drive axles are overweight while the trailer axles have room. Sliding the trailer tandems forward will do what?

    Show answer

    Answer C: Move weight off the drive axles and onto the trailer axles

    Sliding the trailer tandems forward brings the rear support closer to the load, so the trailer axles pick up more weight and the drive axles carry less; sliding them rearward does the opposite.

  18. 18. What is the driver responsible for when a load is covered with a tarp?

    Show answer

    Answer C: Fastening it so it cannot flap free, block a mirror, or come off in the wind

    A tarp that works loose can tear away, block the driver view or the view of others, and become a hazard for the traffic behind.

  19. 19. A dispatcher tells you to take a trailer you believe is loaded badly enough to be unsafe. What should you do?

    Show answer

    Answer C: Refuse to move it until the load has been made safe

    The driver may not operate a vehicle whose cargo is not properly distributed and secured, and an instruction from an employer does not change that.

  20. 20. What is checked about the engine cooling system during the engine compartment inspection?

    Show answer

    Answer C: That the coolant level is adequate and the radiator and hoses are not leaking

    A low coolant level or a leaking hose leads to overheating, which can stop the vehicle in a place where stopping is dangerous.

  21. 21. Why is a leaking exhaust system on a commercial vehicle dangerous to the driver?

    Show answer

    Answer B: It can let carbon monoxide reach the cab, where it can poison the occupants

    Exhaust gas contains carbon monoxide, which has no smell and dulls the driver judgment long before it becomes obvious that anything is wrong.

  22. 22. You have a part load that fills only a third of a long trailer. How should it be placed?

    Show answer

    Answer C: Spread out and centerd side to side, so the weight sits over the axles

    A part load is spread over as much of the floor as possible and kept centerd, so no axle is overloaded and the vehicle stays balanced from side to side.

  23. 23. Most rollovers of loaded trucks on exit and entrance ramps happen for which reason?

    Show answer

    Answer B: The ramp was taken faster than the load could tolerate

    A posted ramp speed is set for cars, and a loaded trailer with a high center of gravity can roll at a speed a car would take easily.

  24. 24. You are about to cross a long, high bridge with a light load in gusty wind. What should you do?

    Show answer

    Answer C: Slow down and be ready for a sudden push

    Wind is strongest where a bridge leaves the shelter of the land, and lower speed gives you time to correct when the first gust hits.

  25. 25. Why must tiedowns be rechecked during a trip even when they were tight at the start?

    Show answer

    Answer C: Road vibration and cargo movement can loosen them as the miles go by

    Straps and chains settle and loosen as the vehicle bounces and the cargo shifts slightly, so the load must be rechecked at the required intervals.

  26. 26. What does the gross vehicle weight rating of a vehicle describe?

    Show answer

    Answer A: The maximum loaded weight of that single vehicle, as specified by the manufacturer

    The rating is the manufacturer figure for the loaded weight of one vehicle, so it is a limit fixed in advance rather than a measurement of the load on board today.

  27. 27. You are inspecting the vehicle alone and need to confirm that the stop lights work. Which method is correct?

    Show answer

    Answer A: Have a helper press the brake pedal, or apply the brake in a way that keeps it on while you check from outside

    Stop lights are checked from outside the vehicle while the brakes are applied, so a helper or a brake held on is needed.

  28. 28. What can repeated violations of the federal phone and texting rules cost a commercial driver?

    Show answer

    Answer D: Disqualification of the commercial driver license

    Multiple convictions for using a hand-held phone or texting while driving a commercial vehicle lead to disqualification, on top of fines for driver and carrier.

  29. 29. Which set of emergency equipment must be carried on a commercial motor vehicle?

    Show answer

    Answer D: A fire extinguisher, spare electrical fuses unless the vehicle has circuit breakers, and warning devices

    The required kit is a properly charged and rated fire extinguisher, spare fuses when the vehicle uses them, and warning devices for a stopped vehicle.

  30. 30. The brake pedal goes to the floor in a vehicle with hydraulic brakes. What can you do to build some braking pressure?

    Show answer

    Answer B: Pump the brake pedal rapidly, which may bring back enough pressure to slow the vehicle

    Pumping can restore some hydraulic pressure; along with downshifting and the parking brake it is one of the ways to stop when the pedal fails.

  31. 31. Why does a cracked frame rail or cross member make a vehicle unsafe?

    Show answer

    Answer B: The frame carries the whole load, and a crack can spread until the structure fails

    The frame is the backbone that supports the body, the load and the running gear, so a crack in it is a structural failure that grows with every mile.

  32. 32. A car that passed you on the right slows and stays alongside your trailer. What is the best response?

    Show answer

    Answer D: Ease off the accelerator so the car can move clear

    A vehicle sitting beside a trailer is in a blind area and has nowhere to go if you need the lane, so the safest fix is to let it get ahead or behind.

  33. 33. In very hot weather, how often should you check the tires during a trip?

    Show answer

    Answer D: About every two hours or every 100 miles

    Heat raises tire pressure and can lead to blowouts, so tires are checked about every two hours or 100 miles when it is very hot.

  34. 34. During the engine compartment check, which leaks are you looking for?

    Show answer

    Answer D: Fuel, coolant, engine oil, power steering fluid and battery fluid

    Every fluid in the compartment matters, because a fuel leak is a fire risk and a loss of coolant, oil, steering fluid or electrolyte can disable the vehicle.

  35. 35. You are about to slow down sharply on a highway to make a turn into a narrow driveway. How can you warn the drivers behind you?

    Show answer

    Answer C: Tap the brake pedal a few times so the brake lights flash before you slow down

    A few light taps flash the brake lights and give following drivers an early warning that you are about to slow or stop.

  36. 36. What should be checked about the power steering system in the engine compartment?

    Show answer

    Answer D: That the fluid level is correct and the hoses and pump are not leaking

    Losing power steering fluid means losing steering assistance, which can happen suddenly and makes a heavy vehicle very hard to turn.

  37. 37. You are about to back across a quiet street into a driveway. Which of these is good practice before you start to move?

    Show answer

    Answer B: Turn on the four-way flashers and sound the horn to alert anyone nearby

    Warning other road users and pedestrians before a reverse maneuver gives them the chance to stop or move clear before the vehicle starts back.

  38. 38. When turning left, what should a driver of a long vehicle do before beginning the turn?

    Show answer

    Answer B: Reach the center of the intersection so the rear wheels clear the corner

    The rear wheels follow a tighter path than the front, so the vehicle must reach the center of the intersection before the turn begins.

  39. 39. What does a front-end header board on a van or flatbed protect against?

    Show answer

    Answer A: Cargo moving forward toward the cab in a crash or hard stop

    The header board, often called a headache rack, blocks forward movement of the load toward the driver.

  40. 40. Which windshield condition should be reported during the inspection?

    Show answer

    Answer B: Cracks or dirt that get in the way of your view of the road

    The windshield must give a clear view; damage or grime in the driver line of sight is a safety defect.

  41. 41. When traction is poor, such as on packed snow, how should you speed up?

    Show answer

    Answer C: Very gradually, so the drive wheels do not spin

    Gentle throttle keeps the drive wheels from breaking traction, because spinning wheels give up both grip and directional control.

  42. 42. What is the correct way to test the parking brake before a trip?

    Show answer

    Answer C: With the parking brake set, put the vehicle in a low gear and gently try to move forward

    A parking brake that holds against a gentle pull in low gear is working; if the vehicle moves, the brake needs adjustment or repair.

  43. 43. You are moving an oversized load under a permit that requires a pilot vehicle. What is the pilot vehicle there to do?

    Show answer

    Answer B: Warn other traffic and check the route ahead for clearances and hazards

    Escort or pilot vehicles warn approaching traffic and scout the route for low bridges, narrow spots and other hazards that a wide or long load cannot pass.

  44. 44. Why must a bent, cracked or badly seated lock ring be reported?

    Show answer

    Answer D: It can come off under pressure and let the tire and rim separate violently

    The lock ring holds the assembly together against the full pressure of the tire, so a damaged ring can release with enough force to kill.

  45. 45. Rust streaks are running outward from the lug nuts on one wheel. What does this most likely indicate?

    Show answer

    Answer C: The lug nuts may be loose

    Rust trails spreading from the nuts are a classic sign that the nuts have worked loose and the wheel has been moving on the studs.

  46. 46. Why should the radiator cap never be removed while the engine is hot?

    Show answer

    Answer A: The cooling system is under pressure and scalding coolant can be sprayed out

    A hot cooling system holds pressurized coolant above its normal boiling point, so releasing the cap can throw boiling liquid and steam at whoever is holding it.

  47. 47. On packed snow, how much should a commercial driver reduce speed?

    Show answer

    Answer D: By about one half or more

    Packed snow costs far more traction than rain, so speed should be cut by half or more.

  48. 48. Which shock absorber condition is a defect?

    Show answer

    Answer C: A shock that is leaking, broken or disconnected at either mounting

    A shock that has lost its fluid or its mounting no longer damps the suspension, so the wheel bounces and loses contact with the road.

  49. 49. How should the headlamps be checked during the pre-trip inspection?

    Show answer

    Answer A: By switching on both low beam and high beam and confirming each one works outside

    Both beams are separate circuits, so each is switched on in turn and confirmed from outside the vehicle where the lamps can actually be seen.

  50. 50. The scale shows that your combination is over the legal gross weight. Why will sliding the tandems not fix it?

    Show answer

    Answer B: Because sliding the axles changes where the weight sits, not how much there is

    Repositioning axles redistributes weight between axle groups; when the total is too high, freight has to come off the vehicle.